Serving the Concord area  ·  (980) 304-7168  ·  Open Mon-Sun 7am-7pm
📞 (980) 304-7168 Free Quote

Metal Roofing in Cornelius, NC (28031) · Local Professionals

Concord Metal Roofing · Fast response in Cornelius and the Concord area · Free estimate 24h

✅ Licensed Contractor 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
+347Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured

Cornelius is a lake town with a roofing problem that comes off the water. Wind rolls across Lake Norman, hits the subdivisions off West Catawba Avenue, and finds every loose fastener and lifted seam on the block. The housing stock runs from 1990s and 2000s brick and vinyl homes in neighborhoods like The Peninsula and Jetton Cove to older lake cottages near the Davidson line, and most of those roofs were never built for the gusts that come with a summer squall.

We are Concord Metal Roofing, based just up the road in Concord, and Cornelius is one of our regular stops. If you live off Bailey Road or down near Ramsey Creek Park, you have probably seen the kind of wind damage we get called out for: a few shingles gone after a storm, then a leak in the guest room ceiling three weeks later. We install, repair, and replace metal roofs across 28031, and we know what lakefront wind does to a roof over time.

Metal Roofing in Cornelius (28031)

Cornelius sits on the east side of Lake Norman, and that location drives most of the roofing work here. The lots near the water are often tight, with mature oaks and pines close to the house, which means access for a crew and a dumpster can be a real puzzle. The ground is Piedmont red clay, so drainage matters. We see gutters that back up and splash back onto fascia boards, and we see downspouts that dump water right at the foundation. On the inland side, the big subdivisions off West Catawba and Bailey Road have steep architectural shingle roofs that take a beating from straight-line wind. When those roofs fail, it is usually at the ridge or the rake, where the wind gets under an edge and peels. Standing seam metal, with hidden fasteners and a continuous panel, holds up better in that kind of exposure. We also work on the older cottages and ranch homes closer to the Davidson border, where a low-pitch roof and a brick chimney mean flashing details have to be done right or you get a leak at the first ice storm.

Our team has been working in Cabarrus and Mecklenburg counties for years, and we have done enough roofs in Cornelius to know the local inspectors and the HOA review committees. We are fully insured with general liability and workers' compensation, and we pull the permits that Cornelius and Mecklenburg County require for a re-roof.

Our services in Cornelius

How a Job Works in Cornelius

Step 1 is a free on-site assessment. We come out, get on the roof if it is safe, and look at the panels, fasteners, flashing, and decking. If you have a leak, we find the source, not just the stain on the ceiling. We take photos and give you a written estimate before any work starts. For storm damage, we document everything you need for an insurance claim, though coverage is always up to your carrier.

Step 2 is the work itself. In Cornelius, that often means coordinating with an HOA on panel profile and color before we order materials, and scheduling around the afternoon thunderstorms that roll in off the lake in July and August. On tight lakefront lots, we stage materials in the driveway and use a conveyor or a crane if the roof is steep or the access is narrow. We protect landscaping and keep the site secure at the end of each day.

Step 3 is cleanup and a final walkthrough. We magnet-sweep the yard and driveway for nails, haul away old shingles and metal, and walk the roof with you to show you the finished work. We do not leave until you are satisfied and the property is clean.

Pricing in Cornelius depends on the size and pitch of your roof, the condition of the decking, and how easy it is to get materials to the site. As a ballpark, metal roof installation starts at $8 per square foot, standing seam starts at $10 per square foot, and a full replacement starts at $9 per square foot. If you are retrofitting over existing shingles, that starts at $7 per square foot, but code limits how many layers you can leave in place. Repairs start at $450, and screw replacement or re-fastening starts at $750. Coating and painting start at $2.50 per square foot. We give free estimates, so call (980) 304-7168 and we will come out and put real numbers on your roof, not a phone-book range.

My house is in The Peninsula and the wind off Lake Norman keeps lifting shingles. Will a standing seam roof actually stop that?
Standing seam is a good fit for that exposure. The panels run in long lengths with hidden fasteners, so there are no exposed screw heads or shingle tabs for wind to catch. We also check the edge metal and ridge cap, because that is where wind gets under a roof first. On the lake side of Cornelius, we often recommend a heavier gauge panel and a tighter clip spacing.
A storm just took off part of my roof near Ramsey Creek Park. How fast can you get out there?
We prioritize active leaks and storm damage in Cornelius. Call (980) 304-7168 and we will schedule an inspection, usually within a day or two depending on the weather. If the roof is open, we can tarp it to prevent further water damage while you wait for the insurance adjuster.
What does a typical metal roof replacement cost for a 2,000 square foot house in 28031?
For a house that size with a standard pitch and good access, you are usually looking at somewhere between $16,000 and $24,000 for a standing seam or metal shingle roof, depending on the panel type, color, and whether we need to replace decking. A retrofit over existing shingles can be less. We give a firm written estimate after we see the roof.
Do I need a permit from the Town of Cornelius to replace my roof?
Yes, a full replacement or re-roof typically requires a permit, and the town follows the North Carolina building code. We pull the permit for you and schedule the inspections. If your home is in a historic district or an HOA, there may be additional design review, and we can help you navigate that.
My HOA requires approval for roof color. Can you help with that process in Cornelius?
We deal with HOA architectural review committees regularly in Cornelius. We can provide color samples, panel profile drawings, and manufacturer specs for your submittal. We will not order materials until you have written approval, so you are not stuck with a color the board rejects.
Are you insured for work on my property in Cornelius?
Yes. We carry general liability insurance and workers' compensation coverage for our crew. We can provide a certificate of insurance before we start, and we recommend asking any contractor for one before they set foot on your roof.
What kind of maintenance does a metal roof need in Cornelius to handle the summer storms and winter ice?
Twice a year, check the fasteners and the sealant around flashing and penetrations. After a big storm, look for lifted panels or dented areas. In late fall, clear the gutters and check the snow guards if you have them. Ice dams are less common here than up north, but they can happen on older homes with poor attic insulation. We offer inspections if you want a professional eye on it.
Why choose us?

Trusted professionals in Concord

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Concord

All your work handled by qualified professionals in Concord

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

347+ Verified Client Reviews in Concord

⭐⭐⭐⭐⭐ 4.9/5 · 347 verified Google reviews

Free Quote

Get Your Free Quote

Metal Roofing in Concord · Response within 24h · No commitment · ☎ (980) 304-7168

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Concord ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm